Milnor 36026V7J Bedienerhandbuch

Published Manual Number/ECN: MAI36VXXBE/2003046N• Publishing System: TPAS• Access date: 1/29/2003• Document ECN's: Latest AvailableInstallatio

MSIN0704AE/9271BV ÈRIGID MOUNT WASHER-EXTRACTORINSTALLATION AND SERVICE SAFETYÊHazards During AssemblyELECTROCUTION HAZARD—Contact with high voltage c

MSIN0704AE/9271BV (1 of 2)ÈRIGID MOUNT WASHER-EXTRACTORINSTALLATION AND SERVICE SAFETYÊHazards During AssemblyELECTROCUTION HAZARD—Contact with high

ÊHazards Requiring Immediate ServiceMULTIPLE HAZARDS—Failure to maintain machine in proper working order can result infatal or serious injury to opera

About the Forces Transmitted by Milnor® Washer-extractorsDocument ... BIWUUI02Specified Date ... 20001108As-of Date...

has sufficient strength and rigidity, plus a reasonable factor of safety for both, to support theweight of all the fully loaded machine(s) including t

7\_ccQbi_VDQW9\\ecdbQdY_^c±6Cdi\UACdi\U#&$"FCdi\UQ^THCdi\UGQcXUb5hdbQSd_bcIllustration ExplanationStop! Read the manual

Illustration ExplanationDo not start this machine until the packingmaterials, lifting brackets, etc. with this tagattached or behind this panel are re

Do not start this machine until the part withthis tag is installed on the machine.Do not remove this component from themachine.Install the appropriate

During drain and extract, the cylinder mustrotate counterclockwise when viewed fromhere (rear of machine).During drain and extract, the cylinder mustr

Make cold water connection here.Make hot water connection here.Make third (reuse) water connection here.Hold the connection side of the valve with awr

Please ReadAbout the Manual Identifying Information on the CoverThe front cover displays pertinent identifying information for this manual. Most impor

PELLERIN MILNOR CORPORATIONBIWUUI03 (Published) Book specs- Dates: 20030129 / 20030129 / 20030129 Lang: ENG01 Applic: WUUAvoiding Damage From All

Avoiding Damage From Allied Remote Chemical Delivery SystemsPELLERIN MILNOR CORPORATIONstandards in Riggs and Sherrill, “Textile Laundering Technology

PELLERIN MILNOR CORPORATIONFigure 2: Siphoning From the Chemical Tank into the MachineExamplesLegendP. PumpS. Siphon level. Shading indicates the chem

Avoiding Damage From Allied Remote Chemical Delivery SystemsPELLERIN MILNOR CORPORATIONFigure 3: Dribbling From Chemical Supply Line Into Machine (ass

PELLERIN MILNOR CORPORATION3.4.Dribbling: Locate the entire chemical line below the machine inlet.—Assuming the chemical system does not retain any li

Section 1Installation21

MSIN0206AE/2000304VÈHANDLING AND SETTING PROCEDURESFOR CPE, NPE, Qxx and Vxx WASHER-EXTRACTORSÊHandling Precautions1. Remove the protective coverings

MSIN0206AE/2000304V (1 of 2)ÈHANDLING AND SETTING PROCEDURESFOR CPE, NPE, Qxx and Vxx WASHER-EXTRACTORSÊHandling Precautions1. Remove the protective c

ÊSetting ProceduresSee FIGURE 1 during the following procedures:1. With the machine near the final location, unbolt theshipping skids. Observing all p

ÊSetting ProceduresSee FIGURE 1 during the following procedures:1. With the machine near the final location, unbolt theshipping skids. Observing all p

Table of Contentsfor MAI36VXXBE/2003046N36026V5J, 36026V7J/V7W, 42026V6J/V6W Washer-ExtractorsPage Description Document/ECN1 About this Manual MHI36QX

BTaeXRT2^]]TRcX^]b6T]TaP[Required service connections, (depending on machine model and optional features) are asfollows:1. Piped inlets and outlets (

Table 2: OutletsConnection Description Destination Piping Specifications36026VxJ and 42026V6J Drain3" pipe socket joint, drain tosewerRubber hose

Figure 1: Correct Rotation DuringDrain and Extract (when viewingfront of machine)Figure 2: Line Voltage Switch Set for 240 VoltOperationAT\^eTBWX__X]

2WTRZ2h[X]STaBdaUPRTCheck the perforated cylinder for smoothness. Milnor will not accept responsibility for thecylinder finish after the machine is

30

Section 2Dimensional Drawings31

32

33

34

35

36

37

38

39

40

41

MHI36QXXAE/9541AV (1 of 1)ABOUT THIS MANUALScope—This instruction manual is intended to provide facility requirements and machine installation proce-d

2

3(//(5,10,/125&25325$7,21/,0,7('67$1'$5':$55$17<We warrant to the original purchaser that MILNOR machines including electron

4

How to order repair partsRepair parts may be ordered either from the authorized dealer who sold you thismachine, or directly from the MILNOR factory.